Blood Gas Draw Artefacts
The most critical artefacts in arterial blood gas sampling are air bubbles (affecting PO2 immediately), excessive heparin (falsely lowering ionized calcium/magnesium), delayed analysis beyond 30 minutes at room temperature (affecting multiple parameters), and venous contamination (falsely lowering PO2 and pH).
Major Pre-Analytical Artefacts and Their Impact
Air Bubbles
Air contamination is one of the most immediate and significant sources of error in ABG analysis. Air bubbles interfere with PO2 measurements regardless of storage temperature, causing falsely elevated readings 1. The oxygen in room air (approximately 150 mmHg) equilibrates with the blood sample, artificially raising the measured PO2. All air bubbles must be expelled immediately after collection to prevent this artefact.
Time and Temperature Effects
The timing of analysis is critical for accurate results:
- At room temperature (22°C): PO2 remains stable for up to 120 minutes, pH and glucose for 90 minutes, lactate and PCO2 for only 60 minutes 1
- At 4°C (ice bath): PO2 becomes the least stable parameter and should not be relied upon; however, glucose and lactate remain stable when chilled 1
- Optimal analysis window: All variables remain within clinically acceptable ranges for the first 30 minutes after collection 2. After 45 minutes, PO2 changes exceed clinically relevant thresholds 2
The practical recommendation is to analyze samples within 30 minutes of collection when stored at room temperature, or up to 3.5 hours for pH and 6 hours for PCO2/PO2 when stored in an ice-water bath 3.
Anticoagulation Errors
Excessive heparin causes multiple artefacts 4:
- Ionized calcium and magnesium: Directly chelated by heparin, causing falsely low readings—particularly sensitive to both liquid and dry heparin
- PCO2 and base excess/deficit: Altered by in vitro dilution when too much liquid heparin is used 3
- Optimal technique: Use minimal heparin (just enough to coat the syringe) and avoid dilution of the blood sample
Sample Collection Site Errors
The source of blood dramatically affects accuracy:
- Arterial vs. venous: Central venous and free-flowing capillary blood can be used for screening in normal patients but are subject to considerable error 3. For critically ill patients or those with shock/hypotension (systolic BP <90 mmHg), arterial samples are mandatory 5
- Earlobe capillary samples: Underestimate PO2 by 0.5-1 kPa, though pH and PCO2 remain accurate 5. Repeat arterial sampling is needed if concerns arise about capillary sample accuracy
Physical Sample Integrity Issues
Common physical artefacts include 6, 7:
- Clots: Present in 3-14% of samples, interfering with analysis
- Hemolysis: Causes pseudohyperkalemia through release of intracellular potassium 8
- Inadequate sample volume: Found in 20% of samples, leading to analysis failure 7
- Red cell sedimentation: Occurs in 17% of samples with transport delays 7
Temperature Correction Artefacts
Body temperature variations from normal cause measurable changes in pH and blood gas values when blood is exposed to the analyzer's standard water bath temperature 3. Patient temperature should be documented on requisition forms (though this occurs in only 0.6% of cases in practice 6).
Minimization Strategies
Immediate Collection Practices
- Use appropriate syringes: Dedicated ABG syringes with minimal pre-heparinization
- Expel all air bubbles immediately after collection
- Seal the syringe tip properly: 89% of samples have inadequately sealed tips in practice 7
- Collect adequate volume: Minimum 0.3 mL required
- Use local anesthesia for all ABG specimens except emergencies 5
Transport and Storage
- Analyze within 30 minutes if stored at room temperature
- Use ice-water bath if delays beyond 30 minutes are unavoidable (covers the entire syringe, not just ice cubes placed nearby)
- Label samples immediately: 95.6% lack proper labeling in practice 7
Documentation Requirements
Critical information often omitted includes 6, 7:
- Collection time (missing in 97% of samples)
- Inspired oxygen fraction/FiO2 (missing in 82%)
- Ventilator status (missing in 98%)
- Patient temperature (missing in 99.4%)
All of these parameters are essential for accurate interpretation and must be documented.
Common Pitfalls to Avoid
- Drawing through IV lines: Can cause contamination with heparin or other infusates, artificially prolonging coagulation assays and altering results 8
- Delayed transport: 23% of samples experience transport delays >30 minutes 7
- Inadequate ice coverage: 93% of samples transported with ice have inadequate coverage 6
- Assuming normal SpO2 negates need for ABG: Pulse oximetry will be normal in patients with abnormal pH or PCO2, or with low oxygen content due to anemia 5